Changing to a 12V 360W Power Supply

Why a 360W power supply?

I was trying to print ABS, but I couldn't get good bed adhesion.  The web tells me I need a bed temperature of 100C for printing ABS.  I could only get my bed up to about 80C, even when I let it heat up for an hour or so.

I thought there might be a problem with the wiring, so I checked the voltage to the hotbed while it was heating.  It was 10.4 V instead of 12 V.  So I checked the output of the power supply, thinking I might have some high resistance in the wiring.  Still 10.4 V.  So I adjusted the Vout using the trim pot on the power supply.  The highest I could get was 10.7 V with the heater on.   With the heater off, the output was 13.4 V.  So it was pretty obvious to me that I was running the power supply at its maximum capacity.

Some internet searchingfor under  showed me that I could get a 12V, 30A (360 W) power supply for under $20 (https://www.amazon.com/eTopxizu-Universal-Regulated-Switching-Computer/dp/B00D7CWSCG/ref=sr_1_3?keywords=12V+25A+power+supply&qid=1576126279&sr=8-3) if you are interested).  This power supply is physically a little bit larger than the 12V, 240W supply provided by Tronxy, but it fits in the power supply holder.  I haven't yet worked out the mounting issues, but I think I just need to get the right holes in the base and make sure I cut a new fan outlet in the top cover.


With the new power supply wired up, the bed easily and quickly heated up to 100C.  The hotend also heated up much more rapidly than it had in the past.  So I decided to autotune both the bed and the hotend.

With the procedure below followed, I can easily run 100C on the bed and 240C on the extruder.  This was a great upgrade!

Doing the Autotune

The autotune is accomplished with an M303 command.  For the heated bed:

M303 E-1 C8 S100

For the hotend:

M303 E0 C8 S230

Bed Autotune Parameters

The autotune parameters for the bed were:

Kp= 370.71

Ki = 41.90

Kd = 819.97

In oder to make autotune work, I made a couple of changes, which unfortunately required recompiling Marlin.  You can see my instructions for updating the firmware here.  

The changes I made to the firmware included:

1) Enable PIDTEMPBED

2) Disable BED_LIMIT_SWITCHING

Final PID parameters for Extruder

Set Kp = 8.15, Ki = 0.38, Kd = 43.16 (values came from an autotune cycle)

Updating my Motherboard to SKR v 1.3, TFT 28, and 2208

Well, I  just had my printer set up so it was printing reliably each and every time.  All of my prints wer good.  And then I had a motherboard failure.  I believe it was due to one of the thermistor wires on the heatbed coming loose and touching the 12V supply line on the heated bed, which destroyed the hot bed A/D converter on the Melzi board.  Whether this is the exact case or not, both the hot end and the heated bed thermistors read properly when plugged into the hot end themistor plug.  And they both read Max Temp when plugged into the hot bed thermistor plug.  So it was time for a new motherboard.

I ordered a replacement motherboard from Tronxy.  And waited and waited for it to come.  And thought about some of the neat features that are available on other 3D printers.  Like a cool graphic LCD.  Easy ability to make on-the-fly temperature and speed adjustment.  Filament break detection.  Silent stepping.   And I decided to upgrade my motherboard.

So I ordered a Big Tree Tech SKR v 1.3 motherboard, a Big Tree TechTFT 28 touch screen display, 5 Big Tree Tech TMC 2208 v3.0 UART stepper drivers, and a Biqu Smart Filament Detector.  Now it's time to get them installed.

Installation instructions are pretty sparse on the web.  There are some great YouTube videos that show how to do it.  But although I love watching videos to see how things are done, I hate watching videos to get information that is easily captured in writing.  So I'm going to capture the content of the videos in writing as I work through my install.

You can get the motherboard instructions here.

Configuring the Motherboard Hardware

1. Because I will be using an extenal power supply, rather than powering off the USB, I need to set the power jumper on the board so it connects +5V to INT, rather than connecting +5V to USB.
2. Because I will be using UART stepper drivers, I need to remove all the jumpers from the stepper driver sockets.  Note: I will be using the E1 driver as muy second Z stepper.
3. Install the UART jumpers for each of the stepper motor ports

Adding Octoprint

Well, I finally got my system reliable enough that all I need to do is insert the SD card, select "Print from SD", and then let it run to completion.

With this kind of reliability, it's time to stop using SD cards to print, in my opinion, so I decided to set up Octoprint on a Raspberry Pi.

I purchased a Raspberry Pi 3B+ from Amazon (see this link), along with a case, camera, and longer cable.  Everything came quickly and was of high quality.  I did not purchase a microSD card, as I already had some.  Note that it will require a card of at least 4GB (I used 16)

I downloaded Octopi from the Octoprint website and followed its instructions.  I  used Balena Etcher to flash my .img.

I had to set up the camera using raspi-config.  Under the Advanced menu option I enabled the camera and enabled I2C.  Once I had those items enabled, and the camera plugged into the proper ribbon cable socket (near the middle of the board, rather than at the end), the camera worked great.

It turns out that my wi-fi is really poor in my printing room, so I decided to connect the octopi to my network with a wired ethernet connection.  I edited octopi-wpa-supplicant.txt to comment out the wi-fi configuration.  Now I have success!

Sometimes I have trouble seeing the camera feed.  When this occurs, try killing the webcamd and mjpg_streamer processes, thenrestart webcamd.  That will often get the camera going again.

Part Cooling Fan

After reading a lot on the web, I decided to add a part cooling fan to my Tronxy X3.  I found a couple of fan mounts on Thingiverse.    I found a really simple one, but it was too fragile.  I found some complex ones, but they wouldn't print well without supports, and removing the supports was a pain in the neck.

So I designed my own, using Onshape.  And posted in on Thingiverse  here.

For me, it's a great addition.

Setting the Z-axis Offset

With the autolevel installed, the Z-axis offset is important to set correctly.  It took me a while to figure out what that parameter meant.  Now that I have got it figured out, I'll write it to my blog to  make sure I always remember it.

The Z-axis offset is the Z-coordinate that will be loaded in the controller when the axis is homed.  That means, when my auto-leveler detects a home condition, the Z-axis offset should be the distance between the bed and the nozzle.

This can be measured with feeler gages.  It can also be measured by setting a high Z offset, then manually lowering the Z-axis until the nozzle reaches the bed.  The difference between the original offset and the Z-coordinate when the nozzle touches the bed is the Z offset.

You can also get close, then make fine adjustments.  If your first layer shows that the nozzle is too high, raise the Z-axis offset.  If your first layer shows that the nozzle is too low, lower the Z-axis offset.

To adjust the Z-axis offset in the Marlin firmware, go to Control/Motion/Z offset.  Use the up and down buttons to raise and lower the offset.

Once you get an offset you like, be sure to go to ControlStore Memory to save the settings in permanent memory so they'll be there after you power down your system.

Note: I have found out how to set the Z axis offset in G Code.

Use M851 Z<negative of Z axis offset>

Use M500 to store the current offset to firmware

Use M501 to load the current offset (and other settings) from firmware.

My Tronxy has a Z offset of about 4.9 mm.

Adding Autolevel

When I ordered my printer, it was claimed to be an autoleveling printer (X3A).  What actually came was a manual leveling printer (X3).  When I asked about this, I was given a discount that was enough to purchase an inductive sensor that will mount to my print head.  Now I just need to change the firmware.

Some background is given here: repetier firmware discussion on autolevel

This explanation makes it seem that I need to get repetier firmware 0.92 or newer (there is some mention of 1.0, effective 14 Jan 2017).

I will also need to know what the configuration for my printer is.  I'm not sure exactly what it is.   I have tried to get firmware source code for a Tronxy X3 so that I know what the existing settings are.

I have obtained a copy of Marlin firmware for an X3 (but my printer has repetier firmware).

I have obtained what purports to be a copy of Reptetier V1.0 for tronxy.  https://github.com/worder/tronxy-x3-repetier-firmware

I'd also like to extract the current code from the printer, so if I have problems with updating, I can go back to a working printer.

There is information on Tronxy firmware here: https://github.com/TronxyX3/Wiki/wiki.    It appears that the Autolevel firmware is Marlin, and the non-Autolevel firmware is Repetier.

I have now figured out how to upload new firmware to the Tronxy, and can go between Marlin and Repetier at will.  A log of what I did to make it work is found here.